| SEALED POWER : 2555A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 56.5200 ;
- Housing Bore Max (in): 2.2252 ;
- Housing Bore Min (MM): 56.5070 ;
- Housing Bore Min (in): 2.2247 ;
- Oil Clearance Max (MM): 0.0710 ;
- Oil Clearance Max (in): 0.0028 ;
- Oil Clearance Min (MM): 0.0130 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 21.3900 ;
- Overall Length Max (in): 0.8420 ;
- Standard Shaft Max (MM): 53.3400 ;
- Standard Shaft Max (in): 2.1000 ;
- Standard Shaft Min (MM): 53.3150 ;
- Standard Shaft Min (in): 2.0990 ;
- Wall Thickness Max (IN): 0.0622 ;
- Wall thickness Max (MM): 1.5800 ;
|
| SEALED POWER : 2555CP |
Connecting Rod Bearing |
- Housing Bore Max (MM): 56.5200 ;
- Housing Bore Max (in): 2.2252 ;
- Housing Bore Min (MM): 56.5070 ;
- Housing Bore Min (in): 2.2247 ;
- Oil Clearance Max (MM): 0.0710 ;
- Oil Clearance Max (in): 0.0028 ;
- Oil Clearance Min (MM): 0.0130 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 21.3900 ;
- Overall Length Max (in): 0.8420 ;
- Standard Shaft Max (MM): 53.3400 ;
- Standard Shaft Max (in): 2.1000 ;
- Standard Shaft Min (MM): 53.3150 ;
- Standard Shaft Min (in): 2.0990 ;
- Wall Thickness Max (IN): 0.0622 ;
- Wall thickness Max (MM): 1.5800 ;
|
| SEALED POWER : 3760A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 60.3120 ;
- Housing Bore Max (in): 2.3745 ;
- Housing Bore Min (MM): 60.3000 ;
- Housing Bore Min (in): 2.3740 ;
- Oil Clearance Max (MM): 0.0760 ;
- Oil Clearance Max (in): 0.0030 ;
- Oil Clearance Min (MM): 0.0180 ;
- Oil Clearance Min (in): 0.0007 ;
- Overall Length Max (MM): 18.3100 ;
- Overall Length Max (in): 0.7210 ;
- Standard Shaft Max (MM): 57.1370 ;
- Standard Shaft Max (in): 2.2495 ;
- Standard Shaft Min (MM): 57.1170 ;
- Standard Shaft Min (in): 2.2487 ;
- Wall Thickness Max (IN): 0.0619 ;
- Wall thickness Max (MM): 1.5720 ;
|
| SEALED POWER : 4020A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 53.9880 ;
- Housing Bore Max (in): 2.1255 ;
- Housing Bore Min (MM): 53.9620 ;
- Housing Bore Min (in): 2.1245 ;
- Oil Clearance Max (MM): 0.1020 ;
- Oil Clearance Max (in): 0.0040 ;
- Oil Clearance Min (MM): 0.0230 ;
- Oil Clearance Min (in): 0.0009 ;
- Overall Length Max (MM): 18.2900 ;
- Overall Length Max (in): 0.7200 ;
- Standard Shaft Max (MM): 50.7820 ;
- Standard Shaft Max (in): 1.9993 ;
- Standard Shaft Min (MM): 50.7590 ;
- Standard Shaft Min (in): 1.9984 ;
- Wall Thickness Max (IN): 0.0621 ;
- Wall thickness Max (MM): 1.5770 ;
|
| SEALED POWER : 44210CP |
Connecting Rod Bearing |
- Housing Bore Max (MM): 46.0120 ;
- Housing Bore Max (in): 1.8115 ;
- Housing Bore Min (MM): 45.9990 ;
- Housing Bore Min (in): 1.8110 ;
- Oil Clearance Max (MM): 0.0640 ;
- Oil Clearance Max (in): 0.0025 ;
- Oil Clearance Min (MM): 0.0130 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 16.6400 ;
- Overall Length Max (in): 0.6550 ;
- Standard Shaft Max (MM): 42.9870 ;
- Standard Shaft Max (in): 1.6924 ;
- Standard Shaft Min (MM): 42.9720 ;
- Standard Shaft Min (in): 1.6918 ;
- Wall Thickness Max (IN): 0.0591 ;
- Wall thickness Max (MM): 1.5010 ;
|
| SEALED POWER : 63760A |
Connecting Rod Bearing |
- Displacement: 231, Even Fire ;
- Engine Family: V6 ;
- Housing Bore Max (MM): 60.3120 ;
- Housing Bore Max (in): 2.3745 ;
- Housing Bore Min (MM): 60.3000 ;
- Housing Bore Min (in): 2.3740 ;
- Manufacture: Buick ;
- Material: A-Series aluminum bearings ;
- Oil Clearance Max (MM): 0.0760 ;
- Oil Clearance Max (in): 0.0030 ;
- Oil Clearance Min (MM): 0.0180 ;
- Oil Clearance Min (in): 0.0007 ;
- Overall Length Max (MM): 18.3100 ;
- Overall Length Max (in): 0.7210 ;
- Set Type: Rod Set ;
- Standard Shaft Max (MM): 57.1370 ;
- Standard Shaft Max (in): 2.2495 ;
- Standard Shaft Min (MM): 57.1170 ;
- Standard Shaft Min (in): 2.2487 ;
- Wall Thickness Max (IN): 0.0619 ;
- Wall thickness Max (MM): 1.5720 ;
|
| SEALED POWER : 64020A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 53.9880 ;
- Housing Bore Max (in): 2.1255 ;
- Housing Bore Min (MM): 53.9620 ;
- Housing Bore Min (in): 2.1245 ;
- Oil Clearance Max (MM): 0.1020 ;
- Oil Clearance Max (in): 0.0040 ;
- Oil Clearance Min (MM): 0.0230 ;
- Oil Clearance Min (in): 0.0009 ;
- Overall Length Max (MM): 18.2900 ;
- Overall Length Max (in): 0.7200 ;
- Standard Shaft Max (MM): 50.7820 ;
- Standard Shaft Max (in): 1.9993 ;
- Standard Shaft Min (MM): 50.7590 ;
- Standard Shaft Min (in): 1.9984 ;
- Wall Thickness Max (IN): 0.0621 ;
- Wall thickness Max (MM): 1.5770 ;
|
| SEALED POWER : 82555A |
Connecting Rod Bearing |
- Oil Clearance Min (MM): 0.0130 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 21.3900 ;
- Overall Length Max (in): 0.8420 ;
|
| SEALED POWER : 82555CP |
Connecting Rod Bearing |
- Displacement: 302, 305, 307, 350 ;
- Engine Family: Small Block ;
- Housing Bore Max (MM): 56.5200 ;
- Housing Bore Max (in): 2.2252 ;
- Housing Bore Min (MM): 56.5070 ;
- Housing Bore Min (in): 2.2247 ;
- Manufacture: Chevrolet ;
- Material: Overplated copper-lead alloy ;
- Oil Clearance Max (MM): 0.0710 ;
- Oil Clearance Max (in): 0.0028 ;
- Oil Clearance Min (MM): 0.0130 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 21.3900 ;
- Overall Length Max (in): 0.8420 ;
- Set Type: Rod Set ;
- Standard Shaft Max (MM): 53.3400 ;
- Standard Shaft Max (in): 2.1000 ;
- Standard Shaft Min (MM): 53.3150 ;
- Standard Shaft Min (in): 2.0990 ;
- Wall Thickness Max (IN): 0.0622 ;
- Wall thickness Max (MM): 1.5800 ;
|
| SEALED POWER : 84825A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 57.1500 ;
- Housing Bore Max (in): 2.2500 ;
- Housing Bore Min (MM): 57.1380 ;
- Housing Bore Min (in): 2.2496 ;
- Oil Clearance Max (MM): 0.0520 ;
- Oil Clearance Max (in): 0.0020 ;
- Oil Clearance Min (MM): 0.0100 ;
- Oil Clearance Min (in): 0.0004 ;
- Overall Length Max (MM): 19.2500 ;
- Overall Length Max (in): 0.7580 ;
- Standard Shaft Max (MM): 53.9620 ;
- Standard Shaft Max (in): 2.1245 ;
- Standard Shaft Min (MM): 53.9480 ;
- Standard Shaft Min (in): 2.1240 ;
- Wall Thickness Max (IN): 0.0621 ;
- Wall thickness Max (MM): 1.5770 ;
|
| SEALED POWER : 45000A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 51.0210 ;
- Housing Bore Max (in): 2.0087 ;
- Housing Bore Min (MM): 51.0010 ;
- Housing Bore Min (in): 2.0079 ;
- Oil Clearance Max (MM): 0.0250 ;
- Oil Clearance Max (in): 0.0010 ;
- Overall Length Max (MM): 15.6000 ;
- Overall Length Max (in): 0.6140 ;
- Standard Shaft Max (MM): 48.0010 ;
- Standard Shaft Max (in): 1.8898 ;
- Standard Shaft Min (MM): 47.9910 ;
- Standard Shaft Min (in): 1.8894 ;
- Wall Thickness Max (IN): 0.0588 ;
- Wall thickness Max (MM): 1.4940 ;
|
| SEALED POWER : 64990A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 60.3380 ;
- Housing Bore Max (in): 2.3755 ;
- Housing Bore Min (MM): 60.3150 ;
- Housing Bore Min (in): 2.3746 ;
- Oil Clearance Max (MM): 0.0690 ;
- Oil Clearance Max (in): 0.0027 ;
- Oil Clearance Min (MM): 0.0180 ;
- Oil Clearance Min (in): 0.0007 ;
- Overall Length Max (MM): 19.6100 ;
- Overall Length Max (in): 0.7720 ;
- Overall Length Min (MM): 19.3550 ;
- Overall Length Min (in): 0.7620 ;
- Standard Shaft Max (MM): 57.1370 ;
- Standard Shaft Max (in): 2.2495 ;
- Standard Shaft Min (MM): 57.1220 ;
- Standard Shaft Min (in): 2.2489 ;
- Wall Thickness Max (IN): 0.0622 ;
- Wall thickness Max (MM): 1.5800 ;
|
| SEALED POWER : 44970P |
Connecting Rod Bearing |
- Part Material: A-Series aluminum ;
|
| MAHLE / CLEVITE : CB1797A |
Connecting Rod Bearing |
- 1.9984: 1.9994 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1648P |
Connecting Rod Bearing |
- 2.1235: 2.1245 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1776A |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1238A |
Connecting Rod Bearing |
- 1.9984: 1.9994 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663A |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663P |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1238P |
Connecting Rod Bearing |
- 1.9984: 1.9994 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1874A |
Connecting Rod Bearing |
- 2.2488: 2.2495 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663VXN |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1827H |
Connecting Rod Bearing |
- 1.9291: 1.9297 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663HND |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1443A |
Connecting Rod Bearing |
- 2.2487: 2.2499 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663HN |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663VN |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663HXND |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB663HXN |
Connecting Rod Bearing |
- 2.099: 2.1 ;
- Min Shaft: Max Shaft ;
|
| MAHLE / CLEVITE : CB1877A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1879A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1875A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1806A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| ITM ENGINE COMPONENTS : 4B9557 |
Connecting Rod Bearing |
|
| ITM ENGINE COMPONENTS : 4B9559 |
Connecting Rod Bearing |
|
| ENGINETECH : BB1001 |
Connecting Rod Bearing |
- Housing Bore: 2.0079-2.0087 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0010 in ;
- Shaft Diameter: 1.8894-1.8898 in ;
- Wall Thickness: 0.0583-0.0588 in ;
- Width: 0.614 IN ;
|
| ENGINETECH : BB1010 |
Connecting Rod Bearing |
- Housing Bore: 1.8504-1.8513 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0011-0.0024 in ;
- Shaft Diameter: 1.7320-1.7323 in ;
- Wall Thickness: 0.0584-0.0589 in ;
- Width: 0.618 IN ;
|
| ENGINETECH : BB1015 |
Connecting Rod Bearing |
- Housing Bore: 1.8895-1.8905 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0011-0.0020 ;
- Shaft Diameter: 1.7713-1.7717 in ;
- Wall Thickness: 0.0582-0.0587 in ;
- Width: 0.626 IN ;
|
| ENGINETECH : BB105J |
Connecting Rod Bearing |
- Housing Bore: 2.0519-2.0525 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0004-0.0022 in ;
- Shaft Diameter: 1.9291-1.9297 in ;
- Wall Thickness: 0.0604-0.0609 in ;
- Width: 0.798 in ;
|
| ENGINETECH : BB129J |
Connecting Rod Bearing |
- Housing Bore: 2.3746-2.3755 in ;
- Number of Bearings: 6 ;
- Oil Clearance: 0.0007-0.0027 in ;
- Shaft Diameter: 2.2489-2.2495 in ;
- Wall Thickness: 0.0617-0.0622 in ;
- Width: 0.772 in ;
|
| ENGINETECH : BB133J |
Connecting Rod Bearing |
- Housing Bore: 2.3472-2.3479 in ;
- Number of Bearings: 6 ;
- Oil Clearance: 0.0004-0.0023 in ;
- Shaft Diameter: 2.2044-2.2050 in ;
- Wall Thickness: 0.0704-0.0709 in ;
- Width: 0.730 in ;
|
| ENGINETECH : BB147J |
Connecting Rod Bearing |
- Housing Bore: 1.8110-1.8115 in ;
- Number of Bearings: 4 ;
- Shaft Diameter: 1.6918-1.6924 in ;
- Width: 0.655 IN ;
|
| ENGINETECH : BB253J |
Connecting Rod Bearing |
- Housing Bore: 2.2247-2.2252 in ;
- Number of Bearings: 8 ;
- Oil Clearance: 0.0005-0.0028 in ;
- Shaft Diameter: 2.0992-2.1000 in ;
- Wall Thickness: 0.0614-0.0619 in ;
- Width: 0.842 IN ;
|
| ENGINETECH : BB285J |
Connecting Rod Bearing |
- Housing Bore: 2.1245-2.1255 in ;
- Number of Bearings: 6 ;
- Oil Clearance: 0.0009-0.0040 in ;
- Shaft Diameter: 1.9984-1.9994 in ;
- Wall Thickness: 0.0617-0.0622 in ;
- Width: 0.719 in ;
|
| ENGINETECH : BB310J |
Connecting Rod Bearing |
- Housing Bore: 2.2494-2.2505 in ;
- Number of Bearings: 8 ;
- Oil Clearance: 0.0002-0.0027 in ;
- Shaft Diameter: 2.1235-2.1245 in ;
- Wall Thickness: 0.0619-0.0624 in ;
- Width: 0.760 in ;
|
| ENGINETECH : BB353J |
Connecting Rod Bearing |
- Housing Bore: 2.2267-2.2272 in ;
- Number of Bearings: 8 ;
- Oil Clearance: 0.0009-0.0032 in ;
- Shaft Diameter: 2.0992-2.1000 in ;
- Wall Thickness: 0.0624-0.0629 in ;
- Width: 0.842 IN ;
|
| ENGINETECH : BB624J |
Connecting Rod Bearing |
- Housing Bore: 2.3740-2.3745 in ;
- Number of Bearings: 6 ;
- Oil Clearance: 0.0008-0.0036 in ;
- Shaft Diameter: 2.2487-2.2495 in ;
- Wall Thickness: 0.0613-0.0619 in ;
- Width: 0.720 in ;
|
| MAHLE / CLEVITE : CB1827A4 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1877A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1835A4 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1874A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1920H |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1238A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1443A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1776A8 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1797A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1806A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1863A4 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1875A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1879A6 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1920HX |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1948A4 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB663A8 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB663P8 |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1827A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1835A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB1863A |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| GM GENUINE : 89017573 |
Connecting Rod Bearing |
|
| ENGINETECH : BB1059 |
Connecting Rod Bearing |
- Housing Bore: 1.8504-1.8513 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0005-0.0015 in ;
- Shaft Diameter: 1.7320-1.7323 in ;
- Wall Thickness: 0.0583-0.0587 in ;
- Width: 0.567 in ;
|
| GM GENUINE : 12591093 |
Connecting Rod Bearing |
- Outside Diameter (IN): 2.053 ;
- Outside Diameter (MM): 52.134 ;
- Sealed: No ;
- Shaft Diameter (IN): 1.93 ;
- Shaft Diameter (MM): 49.014 ;
|
| GM GENUINE : 12636003 |
Connecting Rod Bearing |
- Outside Diameter (IN): 2.348 ;
- Outside Diameter (MM): 59.636 ;
- Sealed: No ;
- Shaft Diameter (IN): 2.205 ;
- Shaft Diameter (MM): 56.008 ;
|
| GM GENUINE : 89060553 |
Connecting Rod Bearing |
- Inside Diameter (IN): 2.252 ;
- Inside Diameter (MM): 57.19 ;
- Outside Diameter (IN): 2.376 ;
- Outside Diameter (MM): 60.338 ;
- Sealed: No ;
- Shaft Diameter (IN): 2.25 ;
- Shaft Diameter (MM): 57.138 ;
|
| ITM ENGINE COMPONENTS : 4B1702 |
Connecting Rod Bearing |
|
| SEALED POWER : 5070A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 59.637 ;
- Housing Bore Max (in): 2.348 ;
- Housing Bore Min (MM): 59.619 ;
- Housing Bore Min (in): 2.347 ;
- Oil Clearance Max (MM): 0.058 ;
- Oil Clearance Max (in): 0.0023 ;
- Oil Clearance Min (MM): 0.012 ;
- Oil Clearance Min (in): 0.0005 ;
- Overall Length Max (MM): 18.542 ;
- Overall Length Max (in): 0.726 ;
- Standard Shaft Max (MM): 56.007 ;
- Standard Shaft Max (in): 2.205 ;
- Standard Shaft Min (MM): 55.992 ;
- Standard Shaft Min (in): 2.204 ;
|
| SEALED POWER : 65070A |
Connecting Rod Bearing |
|
| ITM ENGINE COMPONENTS : 8B6956 |
Connecting Rod Bearing |
|
| MAHLE / CLEVITE : CB663HNC |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB663HNDC |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| MAHLE / CLEVITE : CB663HXNDC |
Connecting Rod Bearing |
- ALSolid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: NNarrowed for greater crankshaft fillet clearance. ;
- ASteel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: MSteel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- BSteel backed bearings with a conventional babbit lining.: PSteel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- CSteel backed bearings with a copper-lead lining.: RIndicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- DBearing has dowel hole.: SIndicates a set number designation. ;
- GSteel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: VHigh performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- HGHigh performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XBearing has .001” more oil clearance than standard. ;
- HHigh performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VGHigh performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HTHigh performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XXBearing has .002” more oil clearance than standard. ;
- KTriArmor coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: WIndicates a part that is a thrust washer (may also be designated upper or lower). ;
|
| GM GENUINE : 89017700 |
Connecting Rod Bearing |
- Inside Diameter (IN): 2.252 ;
- Inside Diameter (MM): 57.1911 ;
- Outside Diameter (IN): 2.374 ;
- Outside Diameter (MM): 60.3123 ;
- Sealed: No ;
- Shaft Diameter (IN): 2.25 ;
- Shaft Diameter (MM): 57.1475 ;
|
| GM GENUINE : 93744930 |
Connecting Rod Bearing |
|
| GM GENUINE : 93742707 |
Connecting Rod Bearing |
|
| GM GENUINE : 93742708 |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4263SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4363SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4363XP |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4363XPX |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4608SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR4608XP |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR605SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6664SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6664XP |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6664XPX |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6826SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6826XP |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR6826XPX |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR8003SI |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR807HPND |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR807HPNDX |
Connecting Rod Bearing |
|
| KING ENGINE BEARINGS : CR807SI |
Connecting Rod Bearing |
|
